With the newer HD Security Systems using proximity FOBs where the key FOB needs to be close to the bike to start, it is very impoprtant to set your Alarm Override PIN code and know how to use the manual alarm override. If the battery in your FOB dies or you lose your FOB and you have not set your Harley Alarm Override PIN Code, you will not be starting your bike
If you haven't set your own PIN override code for your HD security alarm system...do it now!
2014 & NEWER H-D MOTORCYCLES
(scroll down for pre 2014)
Set/Change Security System Override PIN
(scroll down for how to use the pin code to override)
1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual.
2. With an assigned FOB present, turn IGN key ON with the handlebar kill switch in the OFF position
3. Cycle the Handlebar Kill Switch to RUN - OFF - RUN - OFF - RUN
4. Press LEFT turn signal switch 2 times
5. Press RIGHT turn signal switch 1 time and release
*Current PIN will appear in the odometer. The first digit will be flashing
6. Enter first digit of the new PIN by pressing LEFT turn signal (x) times
7. Press RIGHT turn signal 1 time and release. The second digit will be flashing
8. Enter second digit of the new PIN by pressing LEFT turn signal switch (x) times
9. Press RIGHT turn signal 1 time and release. The third digit will be flashing
10. Enter the third digit of the new PIN by pressing LEFT turn signal (x) times
11. Press the RIGHT turn switch 1 time and release. The forth digit will be flashing
12. Enter forth digit of the new PIN by pressing LEFT turn signal switch (x) times
13. Press the RIGHT turn switch 1 time and release. The fifth digit will be flashing
14. Enter the fifth digit of the new PIN by pressing LEFT turn signal (x) times
15. Before the module rearms, switch the Handelbar Kill Switch to OFF AND turn Ignition Key to OFF to store the new pin in the module.
Using the PIN to Override the Security Alarm
(2014 & Newer Harley Davidson Motorcycles)
1. Turn the IGN key to IGNITION and immediately press and release the LEFT turn signal. The odometer will read 'ENTER PIN'
(NOTE: This will only work if the FOB is not present or dead)
2. Enter the first digit of your PIN by pressing the LEFT turn signal switch (X) times
3. Press the RIGHT turn signal switch 1 time to move to the next digit
4. Enter the second digit of your PIN by pressing the LEFT turn signal switch (X) times
5. Press the RIGHT turn signal switch 1 time to move to the next digit
6. Enter the third digit of your PIN by pressing the LEFT turn signal switch (X) times
7. Press the RIGHTturn signal switch 1 time to move to the next digit.
8. Enter the forth digit of your PIN by pressing the LEFT turn signal switch (X) times
9. Press the RIGHT turn signal switch 1 time to move to the next digit
10. Enter the fifth digit of your PIN by pressing the LEFT turn signal switch (X) times
11. Press the RIGHT turn signal switch 1 time to move to the next digit
12. Press the RIGHT turn signal switch one time and the security system alarm is turned off
PRE 2014 H-D MOTORCYCLES
Set/Change Security System Override PIN
(scroll down for how to use the pin code override)
1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual.
2. With an assigned FOB present, turn IGN key ON - OFF - ON - OFF - ON
3. Press left turn signal switch 3 times
4. Press RIGHT turn signal switch one time and release
*Turn signals will flash 3 times. Current PIN will appear in the odometer. The first digit will be flashing
5. Enter first digit of the new PIN by pressing LEFT turn signal (x) times
6. Press RIGHT turn signal 1 time and release. The second digit will be flashing
7. Enter second digit of the new PIN by pressing LEFT turn signal switch (x) times
8. Press RIGHT turn signal 1 time and release. The third digit will be flashing
9. Enter the third digit of the new PIN by pressing LEFT turn signal (x) times
10. Press the RIGHT turn switch 1 time and release. The forth digit will be flashing
11. Enter forth digit of the new PIN by pressing LEFT turn signal switch (x) times
12. Press the RIGHT turn switch 1 time and release. The fifth digit will be flashing
13. Enter the fifth digit of the new PIN by pressing LEFT turn signal (x) times
14. Before the module rearms, turn ignition key to OFF to store the new pin in the module
Using the PIN to Override the Security Alarm
(Pre 2014 Harley Davidson Motorcycles)
1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window
2. Enter the first digit of your PIN by pressing the LEFT turn signal switch (X) times
3. Press the RIGHT turn signal switch 1 time to move to the next digit
4. Enter the second digit of your PIN by pressing the LEFT turn signal switch (X) times
5. Press the RIGHT turn signal switch 1 time to move to the next digit
6. Enter the third digit of your PIN by pressing the LEFT turn signal switch (X) times
7. Press the RIGHT turn signal switch 1 time to move to the next digit
8. Enter the forth digit of your PIN by pressing the LEFT turn signal switch (X) times
9. Press the RIGHT turn signal switch 1 time to move to the next digit
10. Enter the fifth digit of your PIN by pressing the LEFT turn signal switch (X) times
11. Press the RIGHT turn signal switch 1 time to move to the next digit
12. Press the RIGHT turn signal switch 1 time and the security system alarm is turned off.
SOME VALUABLE TIPS FOR YOUR H-D SECURITY SYSTEM
Change your FOB battery twice a year so you never get stuck with a dead one. I do mine every time I change the clocks forward or back for daylight savings time
Put a contact in you phone for your bike and add the PIN as the phone number. Then in contact notes PUT the basic INSTRUCTIONS to enter the override.
If your bike appears to be locked out, check your surroundings. If your bike is parked near anything that emites RFs it may interfere with the communication between the FOB and the bike. This could include wireless security cameras, newer cars, power lines, etc. Try moving your bike away from these possible sources of interference. If that doesn't work, use the override.
